双工位烧结炉是由洛阳西格马高温电炉生产的高温烧结炉，加热元件采用钽或钨加热区（其他材料可用），额定温度可达2100℃。能够同时处理两个负载，在相同的占地面积内，基本上使产量翻倍。我们的烧结炉广泛应用于电子行业，用于高温烧结或热处理电子元件。循环包括大气制备、加热、快速冷却和控制氧化。

双工位炉同时处理两个负载，在热室加热一个负载，同时冷却底部腔室中的第二个负载。

该炉的可用区域直径为12“x 22”高（305 mm x 559 mm），适用于大批量加工。

该炉有两个腔室，底部腔室用于装卸、冷却和控制氧化，顶部腔室用于烧结。两个腔室的空气都是隔离的。电动升降器将负载堆从底部腔室移动到加热室。

对于钽或钨热区，热区的温度额定可达2100℃。。

高通量10〃或16〃扩散泵系统处理产品加热过程中常见的负载放气。

一个直观的定制人机界面运行完全自动化的循环开始结束。

有关小型或大型烧结炉，请参考我们的其他烧结炉。

two-station sintering furnace is based on our bottom loading sintering furnace, but is capable of simultaneously processing two loads, essentially doubling throughput within the same footprint. Our sintering furnaces are widely found in the electronics instry for sintering or heat treating electronic components at high temperatures. Cycles consist of atmosphere preparation, heating, rapid cooling and controlled oxidation.

The two-station furnace handles two loads simultaneously by heating one load in the hot chamber while cooling the second one in the bottom chamber.

This furnace has a usable zone of 12” diameter x 22” high (305 mm x 559 mm), and is suited for large batch processing.

The furnace features two chambers, a bottom chamber for loading and unloading, cooling and controlled oxidation, and the top chamber for sintering. Both chambers’ atmospheres are isolated. An electric lift moves the load stacks from the bottom chamber into the heating chamber.

The hot zone is capable of temperatures up to 2100℃ with Tantalum or Tungsten hot zones..

A high throughput 10″ or 16″ diffusion pumping system handles load outgassing typically seen ring proct heat-up.

An intuitive customized HMI interface runs completely automated cycles start to finish.

Refer to our other sintering furnaces for smaller or larger models.

一般规格：

采用双容量双负荷炉

热区尺寸12“直径x 22”高（305 mm x 559 mm）

钽或钨加热区（其他材料可用）

额定温度2100℃（3812°F）

+/-10℃可用区温度梯度

底部腔室用于装载和冷却，顶部腔室用于烧结。

氧化结束时的控制

10〃或16〃大容量扩散泵送系统

用于快速负载冷却的气体换热器

电动负载升降机，用于精度的负载移动

带计算机接口的全自动循环

General specifications:

Two load furnace for double capacity of our single-station

Hot zone Size 12” diameter x 22” high (305 mm x 559 mm)

Tantalum or tungsten heating zone (other materials available)

2100℃ (3812 °F) maximum temperature

+/- 10℃ temperature gradient across usable zone

Bottom chamber for loading and cooling, top chamber for sintering.

Controlled oxidation at end of cycle

High-capacity diffusion pumping system 10″ or 16″

Gas heat exchanger for rapid load cooling

Electric load lifts for precise load movement

Fully automated cycles with computer interface

负载提升系统

我们的两梯度烧结炉与我们的单站底装式烧结炉相同，除了负荷提升系统和控制软件。由于该炉同时处理两个负载，它有两个用于垂直移动的电动负载提升机和用于水平旋转负载臂的附加伺服电机。

该机构能够在无需操作员协助的情况下内部切换负载。当顶部腔室中的热循环完成，新的负载准备好烧结时，顶部负载堆栈将下降到底部腔室中，新负载将提升到顶部腔室中。

新降低的热负荷随后在底部冷却，进行可控氧化，准备好后卸载。伺服系统还旋转底腔的负载臂，以便于装卸。

负载支撑臂的负载提升装置在顶部和底部腔室之间起到传输机构和真空密封的作用。

有关该炉的更多详细信息，请参阅我们的单站底装式烧结炉。

Load Lift System

Our two-station furnace sintering furnace is identical to our single-station bottom-loading sintering furnace, with the exception of the load lift system and the control software. As this furnace handles two loads simultaneously, it has two electrical load lifts for vertical movement and additional servo motors to rotate the load arms horizontally.

This mechanism is able to switch loads internally without operator assistance. When the heat cycle in the top chamber is complete and a new load is ready for sintering, the top load stack will lower into the bottom chamber, and the new load will be lifted into the top chamber.

The newly-lowered hot load is then cooled in the bottom, undergoes controlled oxidation, and is unloaded when ready. The servo system also rotates the load arms of the bottom chamber to facilitate loading and unloading.

A load lift for the load support arm acts as both a transfer mechanism and vacuum seal between the top and bottom chamber.

For further details on this furnace refer to our single-station bottom-loading sintering furnace.